
Location: Home > News > Washing knowlege > This page
Abstract:
Sand washers may encounter various problems during long-term operation, affecting washing efficiency and finished sand quality. Timely identification and troubleshooting can avoid unnecessary downtime and production losses.
1. Low Cleaning Efficiency
Causes:
Insufficient water flow or uneven water distribution.
Too high feed rate, exceeding the washer’s processing capacity.
Worn or damaged spiral blades/wheel buckets, reducing stirring effect.
High silt content in raw sand without pre-treatment.
Solutions:
Adjust water flow rate to ensure sufficient washing water.
Reduce feed rate to match the washer’s capacity.
Replace worn spiral blades or wheel buckets in time.
Install a pre-screening process to remove large impurities

2. Excessive Sand Loss
Causes:
Water flow rate is too high, carrying fine sand out with the overflow.
Overflow weir height is too low.
Sand washer speed is too fast, causing fine sand to be washed away.
Solutions:
Reduce water flow rate to prevent fine sand loss.
Adjust the overflow weir height to retain more sand.
Slow down the washer speed to reduce the impact of water on sand particles
3. Overflow of Sludge and Dirty Water
Causes:
Feed rate is too high, exceeding the washer’s treatment capacity.
Sedimentation tank at the bottom is blocked with sludge.
Water flow rate is too high, causing overflow.
Solutions:
Control feed rate within the washer’s rated capacity.
Clean the sedimentation tank and discharge sludge regularly.
Adjust water flow rate to match the processing capacity
4. Abnormal Noise and Vibration
Causes:
Loose bolts or worn bearings.
Foreign objects enter the washing tank, causing collision noise.
Uneven wear of spiral blades or wheel buckets.
Solutions:
Tighten loose bolts and check bearing lubrication.
Stop the machine and remove foreign objects from the tank.
Replace unevenly worn parts to balance the equipment

Common problems in sand washing operations can be effectively solved through regular maintenance and parameter adjustment. By identifying the root cause and taking targeted measures, you can keep the sand washer running stably and ensure the quality of finished sand.
107reservation successful
Which Factors Should Be Considered When Choosing Between a Jaw Crusher and a Hammer Crusher for Basalt Processing?
When discussing sand production processes, two primary methods often come into focus: dry sand making and wet sand making.
The Workflow of a High-Pressure Grinding Mill
Which Factors Should Be Considered When Choosing Between a Jaw Crusher and a Hammer Crusher for Basalt Processing?
When discussing sand production processes, two primary methods often come into focus: dry sand making and wet sand making.
The Workflow of a High-Pressure Grinding Mill
Which Factors Should Be Considered When Choosing Between a Jaw Crusher and a Hammer Crusher for Basalt Processing?
When discussing sand production processes, two primary methods often come into focus: dry sand making and wet sand making.
The Workflow of a High-Pressure Grinding Mill
50R&D engineers
1000+user case representatives
41ypes of products are exported overseas
200+large and medium-sized digital devices
The user purchased two sets of sand production line, each set of equipment includes ZSW490*110 vibrating feeder, PE750*1060 jaw crusher, HST250 single-cylinder cone crusher, JYS1238 sand making machine, YK2460 vibrating screen, 3016 sand washer and so on.
The designed capacity of this sand making project is 200t/h, and the equipment used includes 490*110 vibrating feeder, PE750*1060 jaw crusher, PF1315 impact crusher, 9928 sand making machine, two sets of 2460 vibrating screen, two sets of 920 single screw sand washer, two sets of XSD2816 sand washer, two sets of dewatering screen, and several belt conveyors.
Project configuration: Jaw Crusher PE900*1200, Cone Crusher HST315T, Vertical Shaft Impact Crusher VSI6X1263, Heavy Duty Vibrating Screen 2YKZ3080/3YKZ3080, Vibrating Feeder ZG1220Z/ZSW1360, Twin Screw Sand Washer 2XL1120, Bar Vibrating Feeder ZSW1360B, Bucket Wheel Sand Washing Machine DS4024, dewatering screen TS2450 many types of equipment. They will work together with the whole production line to crush and process the sand trap cobbles and mountain ores into natural sand, mechanism sand, and uniform material.
The finished products of the project are used for high-speed railway construction and neighbouring construction materials, which will strongly promote the local economic development. In the future, Jianye Heavy Industry Company will continue to give full play to its years of practical experience in the sand and gravel aggregate, construction waste resource reuse, industrial powder making, silica sand and other industries, as well as EPC one-stop turnkey services, to cooperate with customers and jointly promote the high-quality, healthy and sustainable development of the sand and gravel industry.
Jiangsu Rugao Calcium Powder Factory purchased two sets of Jianye 4121 high-pressure mills for the production of heavy calcium powder, which is mainly used in the filler industry and coating industry, and now it also maintains a close cooperation relationship with Jianye, and every year Jianye sends technicians or sales managers to visit the user.
The user uses calcined petroleum coke to grind and make powder, and the finished coke powder is mainly used for processing graphite electrodes. In recent years, the price of coke powder rises, the user spends tens of millions of dollars to build a production line with an annual output of 60,000-100,000 tonnes of high-quality coke powder, which is the first phase of the project, using two sets of 6R4528 high-pressure grinding mills of Jianye Company.